Joined on July 22, 2008
Last Post on March 4, 2014
@ March 4, 2014 7:09 PM in Opportunity KnocksI hope no offense was taken. The writer was commenting on heath issues
@ March 4, 2014 6:46 PM in Opportunity KnocksA few weeks back there was an article on MSN about some rather large fellow.The writer was a Kelly Holohan. Same Kelly?
@ February 21, 2014 4:54 PM in Help!! staple-up insulation foil mythIs he saying the fuel bills will drop that much? As long as the R-19 is installed nicely, not a chance.
Last time I checked a home inspectors job was to find defects.
@ February 19, 2014 7:18 PM in Looking for book recommendations!Has anyone ever returned your books? I have 3 of yours laying around the house and people that have nothing to do with heating will browse through them.
@ February 9, 2014 2:01 AM in Where to put Air EliminatorFirst off, what's the deal with the fill-trol valve and the tank almost on the floor?
@ February 5, 2014 10:57 PM in How, exactly doesI've put in several of Alphas and told the HO how great the thing is. It's a little awkward to not have a decent answer for such a neat gizmo. But they love the LED numbers:)
@ January 31, 2014 11:09 PM in A new showSounds nice! That drought thing there seems pretty wild, even by CA standards. Someone once said that CA will never be without a drought. I believe it. I'll tune in.
@ January 28, 2014 9:50 PM in burnham ES2 pilot assemblyNow never touched a ES2. But that the thing even has a pilot?
@ January 27, 2014 11:21 PM in How long in the shower?I know, it's a dumb question. I just don't know what to say to the tenant. She describes how her hair is so complex at washing? I just don't know what to say. I feel silly even asking you. I believe everything is okay with the 40 gal. gas WH. Thanks again.
@ January 26, 2014 11:45 PM in How long in the shower?Hi- Well I have a friend who has a new tenant in his rental. The tenant complains of only getting 15 minutes of hot water. Is there a golden rule out there that says how long a landlord must keep his tenants shower hot?. I'll just leave it at that.
@ January 22, 2014 8:38 PM in Gateway + Aerco + Caleffi = nice job.Good looking stuff. What's with the haters thing?
@ January 21, 2014 11:16 PM in monoflo helpScroll up to the top of the site and click on systems. Click on hot water, then on circulars and then point of no pressure change. Also, wither the pump. For now just take the authors word for it. Explaining that in plain English is a trip.
If it were me I would remove those flow control valves (Ball valves for that matter) and throw on the pumps. Purge thoroughly
BTW while there I would stick the fill valve between the expansion tank and air separator
@ January 21, 2014 8:40 PM in monoflo helpPutting the pumps where the flow control valves are now would allow both loops to see an increase in system loop pressure. You know, pumping away.
@ January 18, 2014 1:16 AM in Question about fitting on Backflow Preventer (BBFP) *with pics*But what I'm wondering is how did Carl come up with 97.3 success rate and 2.7 as a no go?:) Ah, the mysteries abound. What ever came of the poor (27 out a 1000)souls?:)
Oh BTW Carl since you are an apparent numbers guy, do you any hot tips for Sundays football:)?
Until then I'll ponder this guys backflow preventer:)
@ January 17, 2014 6:59 PM in Direct vent pipingJust curios, is the namestake ,from State Farm,have anything to do with the Insurace co.?
@ January 17, 2014 5:56 PM in Water hammer noise after new gas boiler installedBTW- While you're in the fixing stage you may want to get rid of that ell going the expansion tank and fill valve. That port is for air elimanation. All of that pipe has to be full of air. I'll leave it at that. Read the instuctions.Good luck and go Niners!
@ January 15, 2014 5:30 PM in Water hammer noise after new gas boiler installedThe wiring or terminals are on the inlet side on of the valve body. It appears the black circ.(on return)is pulling water from the wrong port of the ZV.
@ January 15, 2014 3:48 PM in Water hammer noise after new gas boiler installedAre you sure the zone valves are pointing in the right direction?
@ January 15, 2014 2:05 PM in Pex in electrcal conduitHere is all I want to do. From the outside of the house drill a hole that ends up in the joist space of the interior. Then slide a EMT until it hits some solid blocking. Then cut the smallest hole , in the sheetrock, just to get an angle drill and bit into. Then start pushing through the EMT. Then move on to the next piece of blocking. until I get to the other end of the house.Then finish off the EMT ends with a connector and plastic bushing and in goes the pex.
The EMT is for support in instead of staples. I would gladly drop 60 bucks for EMT instead of some serious sheetrock work. It's somethig I've never done or seen. I'm aware of Pex growing as it gets hot. There will plent of slack.
It seems harmless to me.But just curios as to any warnings
P.S. it's 3/4 going into 1 inch EMT
@ January 15, 2014 1:48 AM in Pex in electrcal conduitI have a project where I want to minimize drywall patching.I'm thinking of running EMT just as I would for wires, but instead put Pex in it. This would save me supporting the tube every couple feet and much more drywall repair. Seems to me it's okay, Um, is it okay?
@ January 14, 2014 8:16 PM in One of a kind fireplace...Could the cocktail next door to those steaks be implicated??:)